Blue-white FLEX-PRO A2 ProSeries Peristaltic Pump Manuel d'utilisateur

FLEX-PROPeristaltic Metering PumpR5300 Business Drive, Huntington Beach, CA 92649 USAPhone: 714-893-8529 FAX: 714-894-9492E mail: sales@blue-wh

Press and releaseTo select Run Mode Mode 1: Manual Mode 2: 4-20mA input Mode 3: Frequency input Mode 4: Pulse / BatchPress and HoldTo

Mode 0 - SetupPress and Hold to configure:ŸRemote Start / StopŸTFD (Tube Failure Detection) sensitivityŸFVS (Flow Verification Sensor) time delay -

Page 12Flex-ProUsed to remotely start and stop pump using a dry contact closure signal.When activated; CLOSE = START and OPEN = STOP.Set to NO = Remot

Page 13Flex-ProFlex-Pro pump is equipped with a Tube Failure Detection (TFD) system which is designed to stop pump in event pump tube should rupture a

Page 14Flex-ProFlow verification sensor sold separately.Flow verification system is designed to stop pump in an event sensor does not detect flow duri

Page 15Flex-ProFlow Verification Sensor is designed to give you two installation options.Sensor can be installed:!Directly on pumphead of A2 pump, suc

Page 16Flex-ProAvailable on certain models.Sends a configurable 4-20 mA signal, based on pump rotor speed, to an external device. This feature can be

Page 17Flex-ProStep 8You can now modify other settings in Mode 0 or you can exit Setup by; press and hold SELECT RUN MODE button for a few seconds unt

Page 18Flex-ProUsed to manually control speed of pump.Use UP and DOWN arrows to adjust speed while pump is running.To select exact run speed, follow s

Page 19Flex-Pro8.1 Mode 1 - Manual Operation Screen ShotsRuntime Screen Shot 1Display motor speed percentage.Pump Running in Manual OperationRuntime S

Page 2Flex-ProTABLE OF CONTENTSSection Heading Page1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 20Flex-ProUsed to remotely control pump with an incoming 4-20 mA signal.Default setting: 4 mA signal = 0.1% motor speed20 mA signal = 100.0% mot

Page 21Flex-ProStep 7To exit Setup, press and hold SELECT RUN MODE button for a few seconds until you return to Run screen.Step 6mA value linked to mi

Page 22Flex-ProUsed to remotely control pump with an incoming high speed frequency signal. Typically used with flow meters or other external devices.D

Page 23Flex-ProStep 5Pump speed at maximum Frequency will be displayed.To increase value, press and release UP arrow.To decrease value, press and rele

Page 24Flex-ProUsed to remotely control pump with an incoming pulse signal. Can be used with an external foot pedal, a water meter, a PLC, contact clo

Page 25Flex-ProStep 5Number of pulses to trigger pump start will be displayed.To increase value, press and release UP arrow.To decrease value, press a

Page 26Flex-Pro13.0 TFD (Tube Failure Detection)Flex-Pro is equipped with a Tube Failure Detection System which is designed to stop pump and provide

Page 27Flex-ProPump has a built in 3 amp alarm output relay. Relay is pre-configured to energize on tube failure detection (TFD) and on Flow Verificat

Page 28Flex-ProPrior to service, pump clean water through pump and suction / discharge line to remove chemical.Always wear protective clothing, face s

123456Page 29Flex-Pro16.2 Tube InstallationStep 1Press and release stop button to ensure pump is stopped.With pump stopped, press suction side of tube

Congratulations on purchasing Flex-Pro variable speed Peristaltic Metering Pump. A peristaltic pump is a type of positive displacement pump used for p

Page 30Flex-Pro17.0 Pump MaintenanceAlways wear protective clothing, face shield, safety glasses and gloves when working on or near your metering pump

Page 31Flex-Pro12345671234Pump HeadSpacer, BackRoller Assembly Complete (Rotor), For ND and NF TubesTube Assembly, 3/8” tube connect, Norprene ND (.07

Page 32Flex-Pro19.0 Output Versus Fluid Viscosity

Page 33Flex-ProTHIS PAGE INTENTIONALLY LEFT BLANK

LIMITED WARRANTYYour new Flex-Pro pump is a quality product and is warranted for 24 months from date of purchase (proof of purchase is required). The

2.0 Specifications2.1 Materials of constructionWetted components: Non-Wetted components:Enclosure:413 Aluminum (Polyester powder coated)Pump Head:q Va

3.0 FeaturesPeristaltic pump design does not have valves that can clog requiring maintenance.Self priming - even against maximum line pressure. By-pas

Page 64.1 Mounting LocationChoose an area located near chemical supply tank, chemical injection point, and electrical supply. Install pump where it ca

Page 7PipeTee½” male NPT1/4” male NPTDischarge Injection Fitting / Check ValveDischarge Injection Fitting / Check Valve)PipeTeeInstallupwardfor bestre

Risk of electric shock – cord connected models are supplied with a grounding conductor and grounding-type attachment plug. To reduce risk of electric

Risk of electric shock – cord connected models are supplied with a grounding conductor and grounding-type attachment plug. To reduce risk of electric